The noses are an important part because they provide continuity for the treads and risers on the edge of the stairs. Some laminate flooring manufacturers provide nosing accessories, but their laminate planks are not enough for the usual standard staircase measurements.
Owners still have cut their own laminate planks for the treads and risers. Like the hardwood floor, a laminate plank also needs to acclimate first before the installation. Remove the planks from their packaging and put them in an open space with good air circulation for about 48 hours so that they may properly adjust to the humidity and temperature of the house. This important process prevents them from warping, contracting, and expanding later.
Successful laminate installation depends on having a properly leveled subfloor. All these materials should be removed first before the installation.
Since the laminate installation involves gluing and nailing the material to the subfloor, the surface should provide optimal adhesion. Rough surfaces like lumber and plywood are the best choices for laminate staircases because they ensure that the material sticks properly. After taking the right measurements and preparing the staircase, the next step is to prepare the laminate planks before the installation. Get two laminate planks and glue them together so that it matches the width of the tread.
The process for the riser is simple — just measure from the bottom of the step to its top. If a staircase also has a stair spindle, make sure to get its measurements and subtract the surface area it occupies from the laminate stair tread. Cut off any existing bullnose flush with the riser of the stair providing the dimension change does not violate local building codes Fig. Installation of Stair Treads Beginning at the bottom riser, measure and cut a piece of laminate plank to fit flush with the existing stair tread.
If the laminate has an attached foam or fabric, it must be removed. See special instructions above for Audacity Laminate Glue in place by applying a 3 " 7. Refer to construction adhesive label for all recommendations, warnings and safety precautions. Press in place. Measure and cut stair nose to length.
Dry fit the stair nose to the edge of the first tread with the molding nose overlapping the laminate piece on the riser below. Measure the distance from the edge of the stair nose to the next riser Fig. Measure and cut to width and length another piece of laminate plank for the stair tread.
Using a utility knife or table saw, remove the tongue. If the laminate has an attached fabric, it must also be removed.
Apply a bead of construction adhesive in a 3 " 7. On wood subfloors, drill appropriate size holes into the installed stair nose and anchor with 6d finish nails Fig. Set nails using a nail punch.
Fill holes with a repair stick. To avoid shifting over concrete, allow enough time for the construction adhesive to set prior to continuing the installation. This time will vary depending upon the adhesive being used. Apply a bead of adhesive preferably a 5-minute epoxy to the lip of the stair nose. Push pieces together until joint is tight and flush, then remove excess adhesive. Repeat steps 1—12 until installation is complete.
Allow 24 hours of curing time before exposing stairs to traffic. On wood subfloors, drill appropriate size holes into the installed stair nose and anchor with 6d finish nails.
Install the S Quiet Comfort Underlayment leaving a gap between the stair nose and the underlayment one- half the width of the laminate plank. Using a utility knife or table saw, remove the tongue from the laminate plank to be installed to the stair nose. Apply a bead of adhesive preferably a 5-minute epoxy to the lip on the stair nose.
Place the tongue side of the flooring against the stair nose being sure that the laminate surface is flush with the stair nose surface. From this point, continue the installation of the laminate flooring using the installation instructions provided with the laminate flooring.
Using a utility knife or table saw, remove the bottom lip of the stair nose. Following the instructions listed below, set the router bit and manufacture a groove on the stair nose. Use a 7 mm router bit and 7 mm splines for 7 mm products and an 8 mm router bit and 8 mm splines for 8 mm products. Using a utility knife or table saw, remove the tongue or groove from the laminate plank to be installed to the stair nose. Following the instructions listed below, set the router bit and manufacture a groove on the laminate plank.
Apply a bead of Armsrong EverSeal to both sides of one edge of the spline and insert it into the groove of the stair nose. Apply another bead of glue to the top of the exposed portion of the spline. So whats the right way to install laminate flooring on the stairs with a stair nose?
Every home renovation project should start with a clear pre-installation plan. The laminate planks are glued together and cut at the right size.
The right order of installing the material on the stairs is riser first, tread next, and nosing last. Measure the top riser and tread, working your way down the flight of steps. You must work from the top step since you must let the adhesive set for several hours before using the stairs.
Thus, once you glue it on, you cant stand on it and glue the next stair down. If you are using your stair gauge, adjust it, so either edge sits flush against the edges of the wall. Then remove it, set it atop your first vinyl plank, make a mark, and cut it. When measuring your tread, youll need to account for the width of the flush stair nosing.
Measure the width of the nosing, and place it on the subfloor tread. Make a mark along the tread where the nosing ends. Then measure from the back edge of the tread to the mark you just made. This will be the width of your LVP tread. Risers should be measured from the top edge, flush to the edge, to the bottom where they will sit on top of the tread.
Use a spare piece and place it on the tread. Then sit your measuring tape on top of it and measure to the top of the riser. This is how wide your tread will be.
Are you thinking of making your staircase more beautiful using a new vinyl plank flooring, but dont know how to do it yourself? Well, dont worry because there is good news for you. In this guide, we will explain installing vinyl plank flooring on stairs using simple steps. Although it can seem challenging for you at first, please dont lose hope; its not hard to install flooring on stairs.
We are here to make it easier than you think. So, we will begin with what materials and tools you will need and then look at easy-to-follow steps. Lets dive in! Yes, you can put vinyl plank flooring on the stairs. Careful measurement of risers and treads will allow you to adhere planks to your stairs accurately. Install the appropriate nosing piece flush or over the stair tread nose to transition between the tread and riser. When purchasing LVP for stair installation, do your research to determine what type of stair nose piece is available for the type of vinyl plank you want to buy.
Some will have nosings that overlap the end of the tread, while others offer flush versions. If you like the look and feel of flush nosing, then be sure your LVP brand offers it. Installing flush nosing is more time-consuming than overlapping nosing but can make a smoother walk up and down the stairs. Many people prefer to have vinyl planks on stairs due to its durability and relative ease of installation.
0コメント