Use lubricants sparingly during assembly; a light film is all that is required. Use a small brush or cotton swab to apply grease directly to o-rings where they are not accessible QC fitting, M22 fitting. Uncoil high pressure hose and attach one end of hose to base of spray gun. Attach other end of high pressure hose to high pressure outlet on pump. Before connecting garden hose to water inlet, inspect inlet screen A. Clean screen if it contains debris or have it replaced if damaged.
DO NOT run pressure washer if inlet screen is damaged. Run water through your garden hose for 30 seconds to clean out any debris. Connect the garden hose not to exceed 50 feet 15 m in length to the water inlet.
Turn ON the water, press red button B on the gun and squeeze the trigger to purge the pump system of air and impurities. Be sure to read Operator Safety and Operation before using pressure washer. Make sure handle is in place and secure. Check that oil has been added to proper level in the engine crankcase. Add proper fuel to fuel tank. Check for properly tightened hose connections. Check to make sure there are no kinks, cuts, or damage to high pressure hose.
Provide a proper water supply at an adequate flow. Compare the illustrations with your pressure washer, to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. A - Spray Gun — Controls the application of water onto cleaning surface with trigger device. Includes trigger lock. B - Recoil Starter — Used for starting the engine manually.
E - Engine Identification — Provides model, type and code of engine. Please have these readily available if calling for assistance. F - Cleaning Tank — Use to hold up to one half gallon 1. G - High Pressure Outlet — Connection for high pressure hose. H - Identification Label under foot — Provides model and serial number of pressure washer. Warm water will discharge from pump onto ground. This system prevents internal pump damage. Push switch to off position O or OFF for shutting off engine.
N - Air Filter — Protects engine by filtering dust and debris out of intake air. P - Fuel Tank — Fill tank with regular unleaded fuel. Always leave room for fuel expansion. R - High Pressure Hose — Connect one end to water pump and the other end to spray gun. S - Accessory Tray — Provides convenient storage for standard and optional accessories, such as brushes, turbo wands, etc. If you have any problems operating your pressure washer, please call the pressure washer helpline at Engine exhaust contains carbon monoxide, a poisonous.
Even if you do not smell exhaust fumes, you could still be exposed. To start your pressure washer for the first time, follow these instructions step-by-step. This starting information also applies if you have let the pressure washer sit idle for at least.
Place pressure washer near an outside water source capable of supplying water at a flow rate greater than 3. DO NOT siphon supply water. Check that high pressure hose is tightly connected to spray gun and pump. See Assembly section. Make sure unit is in a level position. Connect garden hose to water inlet on pressure washer pump.
Turn ON water, point spray gun in a safe direction, press red button and squeeze trigger to purge pump system of air and impurities. Choose spray tip you want to use, pull back on collar of nozzle extension, insert spray tip and release collar.
Tug on spray tip to make sure it is securely in place. Push engine rocker switch A to on position I or ON. When starting engine, position yourself as recommended and grasp starter grip handle and pull slowly until you feel some resistance.
Then pull rapidly to start engine. Return starter grip handle slowly. Release spray gun trigger and let engine idle for two minutes. Push engine rocker switch to off position O or OFF. ALWAYS point gun in a safe direction and press red button and squeeze spray gun trigger to release retained high water pressure.
The unit is equipped with an accessory tray with places to store your spray gun, nozzle extension, high pressure hose and quick connect spray tips.
Place spray gun through notches on left side of accessory tray as shown. Place nozzle extension in hole on left side of accessory tray as shown. Insert multi—colored spray tips in spaces provided in accessory tray. Hang high pressure hose on hook attached to the right side of the accessory tray as shown.
The quick—connect on the nozzle extension allows you to switch between four different quick connect spray tips. Spray tips can be changed while pressure washer is running once spray gun trigger lock is engaged. The spray tips vary the spray pattern as shown.
Pull back collar on quick—connect and pull current spray tip off. Store spray tips in holder provided on the accessory tray. Pull back on collar, insert new spray tip and release collar. Review use of spray tips. Prepare detergent solution as required by job. Pour detergent into cleaning tank. Make sure garden hose is connected to water inlet.
Check that high pressure hose is connected to spray gun and pump. Turn on water. Apply detergent to a dry surface, starting at lower portion of area to be washed and work upward, using long, even, overlapping strokes. Allow detergent to "soak in" for minutes before washing and rinsing. Reapply as needed to prevent surface from drying. DO NOT allow detergent to dry on prevents streaking. Remove black detergent spray tip from nozzle extension. Select and install desired high pressure spray tip following instructions How to Use Spray Tips.
Keep the spray gun a safe distance from the area you plan to spray. Apply a high pressure spray to a small area, then check the surface for damage. If no damage is found, it is okay to continue cleaning. Start at the top of the area to be rinsed, working down with same overlapping strokes as you used for washing and applying detergent. The system engages to cool the pump by discharging the warm water onto the ground. Follow the hourly or calendar intervals, whichever occurs first.
More frequent service is required when operating in adverse conditions noted below. Replace if perforated or torn. Regular maintenance will improve the performance and extend the life of the pressure washer. See any qualified dealer for service. To receive full value from the warranty, the operator must maintain the pressure washer as instructed in this manual, including proper storage as detailed in Winter Storage and. NOTICE Should you have questions about replacing components on your pressure washer, please call for assistance.
Some adjustments will need to be made periodically to properly maintain your pressure washer. All service and adjustments should be made at least once each season. Follow the requirements in the Maintenance Schedule chart above.
NOTICE Once a year you should clean or replace the spark plug, clean or replace the air filter, and check the spray gun and nozzle extension assembly for wear. A new spark plug and clean air filter assure proper fuel-air mixture and help your engine run better and last longer. DO NOT attempt any oil maintenance on this pump. The pump is pre-lubricated and sealed from the factory, requiring no additional maintenance for the life of the pump.
Maintenance, replacement, or repair of the emissions control devices and systems may be performed by any non-road engine repair establishment or individual.
See the Emissions Warranty. Check water inlet screen for damage. Check high pressure hose for leaks. Check spray gun and nozzle extension assembly for leaks. Rinse out garden hose to flush out debris. Daily or before use, clean accumulated debris from pressure washer.
Keep linkage, spring and controls clean. Keep area around and behind muffler free from any combustible debris. Inspect cooling air slots and openings on the pressure washer. These openings must be kept clean and unobstructed. Pressure washer parts should be kept clean to reduce the risk of overheating and ignition of accumulated debris.
Clean it if the screen is clogged or replace it if screen is damaged. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password?
Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Save these original instructions for future reference. All rights reserved. Used under license. Operator Safety Equipment Description Read this manual carefully and become familiar with your pressure washer.
Engine exhaust contains carbon monoxide, a poisonous gas that could kill you in minutes. Even if you do not smell exhaust fumes, you could still be exposed to carbon monoxide gas. Contact with muffler area could cause burns resulting in serious injury. WARNING Starter cord kickback rapid retraction will pull hand and arm toward engine faster than you can let go which could cause broken bones, fractures, bruises, or sprains resulting in serious injury.
Chemicals could cause burns resulting in death or serious injury. WARNING The high pressure stream of water that this equipment produces could cut through skin and its underlying tissues, resulting in serious injury and possible amputation. Spray could splash back or propel objects resulting in serious injury. Excessively low speeds impose a heavy load.
If you have any problems with the assembly of your pressure washer, please call the pressure washer helpline at Unpack Pressure Washer 1. Add fuel to fuel tank. Attach Handle and Accessory Tray 1. See How to Use Accessory Tray. Add Engine Oil 1. Page Cleaning Andapplyingdetergent 6. Apply detergent to a dry surface, starting at lower damage. Page Cleaning Detergent Siphoning Tube 7.
ALWAYS point spray gun in a safe direction and Cleaning Detergent Siphoning Tube squeezespray gun trigger to release retained high if you used the detergent siphoning tube, you must flush it water pressure.
Page Maintenance Maintenance NOTE:Once a year you should clean or replacethe spark plug, clean or replace the air filter, and check the spray gun and nozzle extension assembly for wear. A new spark plug Maintenance Schedule and clean air filter assure proper fuel-air mixture and help Follow the hourly or calendar intervals, whichever occurs your engine run better and last longer.
Remove spray tip from end of nozzle extension. The high pressure hose can develop leaks from wear, 4. Use a small paper clip to free any foreign material kinking, or abuse. Inspect the hose each time before using it. Keepoil level maintained. Make sure pressure washer is on a level surface. Remove oil dipstick and wipe dipstick with clean cloth. Page 21 Change oil while engine is still warm from running, as Service Spark Plug follows: Changethe spark plug every hours of operation or once 1.
Drain fuel tank by running pressure washer until fuel each year, whichever comes first. This will help your engine to start easier and run better. For Sediments or minerals can deposit on pump parts and freeze this reason, we recommend you have a qualified service pump action. You must protect your unit from freezing temperatures. Low pressure spray tip installed. Replacewith high pressure spray tip. Water inlet is blocked. Clear inlet. Inadequatewater supply.
Provide adequatewater flow. Straighten inlet hose, patch leak. Pump has following problems:failure 5. Page 26 2. Nos complace que hayadepositado su confianza en la marca Troy-Bilt.
Page 31 labia de Contenido Seguridad de Operario Derscripci6n del equipo Reglas de seguridad Desembalela Nmpiadoraa presiOn Conecte el manubrio y bandeja accesoria Agregar aceite al motor Agregue combustible Conecte la mangueray el suministro de agua a la bomba Caracteristicas y mandos Sirve para advertir al usuariode un posible riesgo para su inlegridad fisica.
Respirar mon6xido de carbono puede provocar dolor de cabeza,fatiga, mareos, v6mitos, iquemaduras severas e inclusive la muerte. IEI arrancador y otras piezas que rotan pueden accesorios. Lea totalmente el manual deJoperario antes que Consulte C6mo Usar la Bandeja vapores de Accesorios. Agregar aceite al motor IEIfuego o una explosi6n pueden causar iquemaduras severas e inclusive la muerte.
Haga correr el agua a trav6s de la manguera de su Conectela mangueray el surninistrode agua a jardin pot 30 segundos para limpiar cualquier la bomba escombro que se encuentre en ella. Corte el agua. Guarde este manual para referencias futuras. A - Pistola de Rociado-- Controla la aplicaci6n de agua sobre la K - Automdtico se Enfria Sistema -- Los ciclos regan per bomba superficie de limpieza con el gatillo.
Ei retroceso producir quemaduras graves. Siempre que est6 de la boquilla y las puntas de rocio. Coloque el cerrojo de seguridad a la pistola de rociado. Compruebe el nivelde aceite autorizado central. Cambie el aceite cada 50 horas de ese momento en adelante. Los sedimentos de minerales se pueden depositar no tengan apagachispas. Vea Cambio de Aceite del Motor en la secci6n congelamiento. Est,, usando la puntas de roc[o de baja 1.
0コメント